Showing results: 1051 - 1065 of 1142 items found.
-
1100H+ -
Cirris Systems Corporation
The Signature 1100H+ high voltage cable and harness tester embodies the Cirris tradition building testers that are easy-to-use, low-cost, and portable. The large display and user-friendly interface make testing cables quick and intuitive. The 1100H+ offers the latest in technology and usability at an affordable price.
-
CFL PL4 -
Scope T&M Pvt, Ltd.
CFL PL4 Power Cable Fault Locator is a portable, easy to use cable fault pre-location instrument. It uses the Time Domain Reflection (TDR), Secondary Impulse Method / Multiple Impulse method (MIM) and Impulse Current Method (ICM) on low, medium and high voltage cables. Its measuring ranges enable pre-location on cable lengths from 500 m to 64km.
-
M-140HC -
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Easy!:Measurale Load Current at high voltage CV/CVT cables with grounding lines for shield phase.*Epoch-Making!:Can measure phase current of CVT cable just by putting CT head on to the conductors as well as CV cable just by clamping CT to the conductors in a lump.*Low Cost!:Can measure line/leakage current in the same manner as ordinary clamp meters.
-
IPG -
Guth GmbH
The IPG series of equipment can be used for checking the insulation of coils, cables, transformers and isolators. The high voltage is produced with a 50Hz transformer and adjusted by means of a variable transformer by hand or in automatic mode with a motor.
-
1555 -
Fluke Corporation
The Fluke 1555 insulation resistance tester offers digital insulation testing up to 10 kV, making it ideal for testing high voltage equipment including switchgear, motors, generators and cables.
-
Fluke 1555 -
Iconic Engineering Limited
The Fluke 1555 insulation resistance tester offers digital insulation testing up to 10 kV, making it ideal for testing high voltage equipment including switchgear, motors, generators and cables.
-
PCE Instruments
A cable fault meter can locate open power cables, either live or dead (without current), with voltages up to 300 V. A cable fault meter can locate cables, circuits, short circuits and ground wires. To perform these functions, it is not always necessary to disconnect electrically sensitive devices or to disconnect the power from the cable which is being tested. Many cable fault meter devices can also locate ferrous and non-ferrous metals, wood and plastic with high degrees of accuracy.
-
WAFRC -
Wuhan Sangao Electrical Test Installations Limit Co.
AC and DC voltage divider, Mainly composition by the high stability of passive resistance capacitance voltage divider and high precision digital kV table. The divider is passive resistance capacitance, Connected digit kV meter by coaxial cables. Which can be directly read out the AC, DC data measured from the table. This instrument has high precision, convenient operation, can be used instead of the electrostatic voltmeter. Device and the measuring line, power line, manual loaded box in light aluminum alloy, easy to carry and use. This equipment is mainly used for AC and DC high voltage measurement, and is suitable for power system's field measured and Institutions of higher learning laboratory's AC and DC high voltage measurement.
-
Hilkar
Since the rise time of IGBTs are in the range of a few tens of nanoseconds (between 50ns-200ns), even short cables between PWM motor drives and motors cause voltage doubling at the motor terminals due to Travelling Wave Phenomenon as in transmission lines. The insulation of motor windings are prone to failure due to high voltage spikes if necessary precautions are not sufficiently taken. RC Type Output Filter Modules reduce these high voltage spikes to protect motors by connecting to stator terminals.
-
BAUR Transcable 4000/A 80-3 -
BAUR Prüf- und Messtechnik GmbH
Transcable 4000/A 80-3. The transcable 4000/A 80-3 cable test van is equipped with an automatic control system. The high voltage switch unit is enclosed and is actuated electrically with the fully automatic KE 3 control unit.
-
Techno Instrumentation (India) Private Limited
LT to HT 11 kV and 33kV Surge Generator is an all in one solution for thumping, DC high voltage testing(Hipot-test) and burning for effective fault location in LT to HT 11 kV and 33kV cables.
-
Technology Products
This Compact power supply/test set can perform all laboratory and field tests of DC Hipot. A flexible High Voltage Cable is provided at the back for connecting to the test specimen. Available in Rack Mount as well as portable design.
-
PCE Instruments
With certain models of cable detectors you can locate open power cables, either live or dead (without current), with voltages up to 300V. Cable detectors can locate cables, circuits, short circuits and ground points. To perform these functions, it is not necessary to disconnect electrically sensitive devices or to disconnect theCable Detectors to locate open power cables, either live or without current, up to 300V power from the cable which is being tested. Cable detectors can also locate ferrous and non-ferrous metals, wood and plastic with a high level of accuracy.
-
BAUR Transcable 4000/S 70-3 -
BAUR Prüf- und Messtechnik GmbH
Transcable 4000/S 70-3. The transcable 4000 70 kV 3/S cable test van varies in comparison with the transcable 32 kV - 3S in the 70 kV voltage level. The system is controlled with the MGS semi-automatic control unit. The high voltage switch unit is 3-phase, air and solid matter insulated and safe to touch.
-
BAUR Transcable 4000/S 110-1 -
BAUR Prüf- und Messtechnik GmbH
Transcable 4000/S 110-1. The transcable 4000/S 110-1 cable test van is a 110 kV cable fault location system in single-phase version. The system is actuated with the semi-automatic MGS control unit. The high voltage switch unit is single-phase, up to 32 kV, the 110 kV switching level is designed as air-insulated ceiling switch.